|
North American Network Operators Group Date Prev | Date Next | Date Index | Thread Index | Author Index | Historical FTC DNCR issues - Thank you ALL!!
Folks - Perhaps along with soliciting advice from this community I would have been better served to go right to Sister Mary Grace and asked for assistance from a higher authority than even NANOG. God was clearly NOT smiling on us this weekend!! But on the other hand He has deservedly had a few issues with me:-) I believe we are now operating in a stable mode and the application is handling things as it was designed to. We will now be able to focus on the tweaking, adjusting and changes typical of the first few days of a launch of this size and scope. Emails are now flowing and queues are almost gone. I am told we are now compliant with at least major protocol and standards. The reverse DNS issues was a side effect of our hardware problem, and is now working properly. 1) If anyone has comment, suggestions or does still think we are operating amateurishly, please let me know!! I actually may have time to get these issues addressed now. 2) I know we were blocked by many ISPs for varying lengths of time due to mostly to our lack of rDNS. I think we have lost these emails as they were likely accepted I am told we stopped sending permanent cookies Saturday afternoon. This is indeed contrary to the Governments privacy policy. It has to do with Webtrends and our requirements to report statistics. I am told session cookies are still going to be necessary 3) Is this acceptable to the community? We have identified some browser issues, particularly some older versions of Netscape. 4) Any issues being seen out there, we would love to ID and address. It was great to find the NANOG community and even though I am (obviously) not a techie (only one of those lowlife sales people that get folks like you in trouble all the time), I will be hanging around on the periphery and continue my education through this new resource. You have all been helpful and I offer my sincere appreciation. Best Regards, Richard -----Original Message----- From: Mary Grace [mailto:[email protected]] Sent: Sunday, June 29, 2003 1:03 AM To: [email protected] Subject: Newbie network upgrade question, apologies in advance to NANOG NANOG: This message was posted originally on the isp-bgp list, and I was told that it should have been posted on one of the network operator lists or a Cisco list if I really wanted advice on Cisco equipment from veteran network operators who have used this equipment extensively in the past for this application. Please, forgive me if this is not appropriate, but I hope that you will consider it appropriate and not flame me for my ignorance Mary Grace! ******************************* Thank you most graciously for the incredible knowledge that God has given you, and to everyone that has responded so generously to this message that we posted this past week, regarding routers for T3 circuits! I am thankful to you all for sharing your knowledge in response to such a newbie question that I was almost ashamed to ask of you. Since the last email, Mother Superior has talked to our generous contributor from the company who is a T3 circuit provider, and explained this list's advice regarding how it was such a "mismatch between a T3 in one port and a T1 in the other" and how BGP isn't really designed to perform well in a multi-homed situation with such a large difference in bandwidth between the two ports. Thanks to your advice, and the wisdom of our MS, the provider has agreed to donate to our small teaching seminary and convent TWO DS3/T3 45 Mb/s point-to-point HDLC circuits, homed into two different exchange points in two different major cities (NAPs). So, is it still true that we do not need anything more powerful than a 4500 or 4700 to run this system? I believe that is true if we take default routes advertised by the upstream on both sides, and the two diverse-path circuits ARE being advertised out of the same upstream AS, but is it still true if we were nuts enough to want to take full routes anyway from this same provider? And why would we even want to take full routes? It is true that, despite the gracious gift of the two DS3 circuits, we don't have much money to buy a router and so we want to find our what Cisco part numbers are needed for whichever model will support two DS3/T3 and one or two 100base ethernet connections into our internal IP space. Thanks again, and may God bless you all in many rich ways :-) Your most thankful and humble servant before God, Mary Grace At 03:45 PM 6/24/03 -0700, Mike wrote: >Yeah, but 3600's are at least 3-4x more expensive than a 4500 or 4700. > >Mike > >On Wed, 18 Jun 2003, Brian Thoman wrote: > >:| Date: Wed, 18 Jun 2003 10:48:26 -0400 >:| From: Brian Thoman <[email protected]> >:| Reply-To: [email protected] >:| To: [email protected] >:| Subject: [isp-bgp] Re: Newbie Cisco upgrade question, >:| apologies in advance:-) >:| >:| Wouldn't a 3640 or 3660 off of eBay do the same trick? We ran two >DS3's off a 3640 for a while with maxed out RAM. It worked for us. >:| >:| ---------- Original Message ---------------------------------- >:| From: Mike <[email protected]> >:| Reply-To: [email protected] >:| Date: Tue, 17 Jun 2003 00:18:40 -0700 (PDT) >:| >:| >If you're looking for really inexpensive, and don't need full routes, get >:| >a 4500/4700 and put a HSSI card in it. With an external CSU, and cable, >:| >you could probably get the whole package for $600-750 on ebay. >:| > >:| >Otherwise, I would suggest looking at a 7100 series (7120 or 7140) with a >:| >built in DS-3 port (or two). Those can be had for dirt cheap on ebay. They >:| >have all the processing power of a comparable 7200, but they're a >:| >smaller form factor and don't have as many port adapter slots (which it >:| >doesn't sound like you need, anyhow). >:| > >:| >Mike >:| > >:| > >:| >On Mon, 16 Jun 2003, E.B. Dreger wrote: >:| > >:| >:| Date: Mon, 16 Jun 2003 21:54:12 +0000 (GMT) >:| >:| From: E.B. Dreger <[email protected]> >:| >:| Reply-To: [email protected] >:| >:| To: [email protected] >:| >:| Subject: [isp-bgp] Re: Newbie Cisco upgrade question, >:| >:| apologies in advance :-) >:| >:| >:| >:| MG> Date: Sat, 14 Jun 2003 20:43:03 -0400 >:| >:| MG> From: Mary Grace >:| >:| >:| >:| >:| >:| MG> Our tiny little non-profit religious network has been using a >pair of T1 >:| >:| MG> lines running BGP4 for multihoming to two diverse-path >upstream ASNs for >:| >:| MG> many years now. We have our own portable IP address space and >ASN (of >:| >:| MG> course), and have just decided to install our first DS3, >because a new >:| >:| >:| >:| I think that's the first "tiny little non-profit religious >:| >:| network" I've ever heard of that had/needed that kind of >:| >:| bandwidth. You could run a moderate ISP using that... >:| >:| >:| >:| >:| >:| MG> upstream is offerring us $30 per month per meg port for a full >:| >:| MG> HDLC-encapsulated point-to-point DS3 (yippee!). >:| >:| MG> >:| >:| MG> Our quandary is where to go to ask people with lots of clue on >BGP4/eBGP to >:| >:| MG> tell us what the least expensive Cisco router we must buy to >replace the >:| >:| MG> tired little 2600 series we currently have. The router, which >need not be >:| >:| MG> as race-car fast as a 7206VXR NPE400, should be able to take >full routes, >:| >:| >:| >:| Do you really need full tables? For what you're doing, I doubt >:| >:| it. If there is some weird reason why you do, how many full >:| >:| views will you take? >:| >:| >:| >:| >:| >:| MG> so I am told it must have at least 128 meg memory, and it must >be able to >:| >:| >:| >:| Maybe. >:| >:| >:| >:| >:| >:| MG> take a coax DS3 feed in to one card or module from the new >provider, and a >:| >:| >:| >:| Yes. PA-T3 or PA-2T3. >:| >:| >:| >:| >:| >:| MG> lowly DS1 serial port now from an AdTran TSU on the other side >for one of >:| >:| >:| >:| Keep the 2610 in service. >:| >:| >:| >:| >:| >:| MG> the old DS1 providers, but be upgradeable someday to take a >second DS3 >:| >:| >:| >:| No problem. >:| >:| >:| >:| >:| >:| MG> card. OF course, with a DS3 on one side, it has to have a 100base >:| >:| MG> ethernet, unlike our blessed little sturdy cheapie 2610 :-) >:| >:| MG> >:| >:| MG> Again, please forgive this perhaps off-topic question, but who >knows better >:| >:| MG> which router can hit the double scores of least expensive and >able to take >:| >:| MG> full BGP4 routes for a DS3 but you learned and knowledgeable folks? >:| >:| MG> >:| >:| MG> Thanks in advance, and any charitable response that you may be >willing to >:| >:| MG> offer us will have our most humble thanks! >:| >:| >:| >:| 7200 series would be best. No need for VXR. >:| >:| >:| >:| >:| >:| Eddy >:| >:| -- >:| >:| Brotsman & Dreger, Inc. - EverQuick Internet Division >:| >:| Bandwidth, consulting, e-commerce, hosting, and network building >:| >:| Phone: +1 (785) 865-5885 Lawrence and [inter]national >:| >:| Phone: +1 (316) 794-8922 Wichita >:| >:| _________________________________________________________________ >:| >:| DO NOT send mail to the following addresses : >:| >:| [email protected] -or- [email protected] -or- [email protected] >:| >:| Sending mail to spambait addresses is a great way to get blocked. |